Edge-lighting Twiggy, Square 1" Lens Uživatelský manuál stáhnout pdf (Strana 1)

904-TW12-S1-01

SAVE THESE INSTRUCTIONS!

- This instruction shows a typical installation.

- This product is wall mount only.

- This product is dimmable with a low-voltage electronic

dimmer.

- This product must be installed by a qualified electrician.

- The 1RE version mounts to the provided C-1RE-JBOX. The

4SQ version mounts to standard electrical box with plaster

ring or octagon box.

IMPORTANT INFORMATION

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: 773-770-1195

Fax: 773-935-5613

www.edgelighting.com

[email protected]

JUNCTION

BOX

MOUNTING

BRACKET

1: Determine channel orientation. Mount each adjustable

mounting bar to one side of the junction box and secure

them with the provided mounting brackets and two Phillips

screws.

ADJUSTABLE

MOUNTING BAR

PHILLIPS

SCREW

VERTICAL

ORIENTATION

HORIZONTAL

ORIENTATION

JUNCTION

BOX

Section One: Steps For TW12-1RE Version

J-BOX IN

MIDDLE

J-BOX

OFFSET

w/4" SQUARE CANOPY

5: Remove a knockout to install the power line conduit.

6: Install the conduit and run the 120V power wires.

JUNCTION

BOX

STUD

CONDUIT

1RE

box to be mounted.

3: Place the adjustable mounting bars between the studs.

4: Make sure the lips on the adjustable mounting bars are

against the studs. Secure the adjustable bars to the studs

with the eight #8 screws.

Select the location between the two studs for the junction

NOTE: The adjustable mounting bars mount to studs that are spaced

13" to 24" apart.

JUNCTION

BOX

ADJUSTABLE

MOUNTING BAR

STUD

#8 SCREW

FIXTURE LOCATION

CENTER LINE

NOTE: Ensure the opening of the junction box is alinged with the

center of the desired fixture location. If necessary, adjust the junction

box location by loosening the screws and sliding the junction box to

the proper location. Tighten the Phillips screws after adjusting.

Installation Instructions for Twiggy Square Lens 12 VAC

TW12-S1-1RE-_

TW12-S1-4SQ-_

1 2 3 4

Shrnutí obsahu

Strany 1 - IMPORTANT INFORMATION

904-TW12-S1-01SAVE THESE INSTRUCTIONS!- This instruction shows a typical installation.- This product is wall mount only.- This product is dimmable wit

Strany 2

2231231CONDUITDJUNCTIONBOX879TRANSFORMERADJUSTABLE MOUNTING BARS13: Install the drywall and plaster around the junction box opening. Sand and th

Strany 3

Section Three: Install Fixture For Both Versions1: Align the channel to the junction box opening. Make markings to each end of the channel and als

Strany 4 - VOLTAGE DIMMER

4MLOCKING CLIPWALL66: Connect each power supply wire to a fixture body wire with a wire nut.7: Place the wires and wire nut connection inside the

Komentáře k této Příručce

Žádné komentáře

Edge-lighting Twiggy, Square 1" Lens Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Edge-lighting Twiggy, Square 1" Lens. Edge Lighting Twiggy, Square 1" Lens User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Edge-lighting Twiggy, Square 1" Lens Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Edge-lighting Twiggy, Square 1" Lens. Edge Lighting Twiggy, Square 1" Lens User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Edge-lighting Twiggy, Square 1" Lens